Do not ever start the en- cure absolute safety of its operation. Button for setting the tachospeedometer to the programming mode and selecting the programming parameter on the tachospeedometer display 7. Right brake pedal Windshield wiper switch 23. Unscrew the six bolts 4 , remove the lock plate 6 and remove the shank 5. Checking backlashes in steering rod joints After each 250 service hours, check the joints by shaking them by hand or rotat- ing the steering wheel.
Head gaskets are not that expensive. Should I shim the valve open or will it hit the cylinder? Gears shift-and —reverse gear shafts are tight- 32 and 34 are splined-mounted on the ened up by nuts 12, 15, 47 and 50. The oil level must be between the upper and lower marks of the dipstick 3. It purities by a coarse fuel filter 3 refer to provides the three-stage purification. Check and adjust valve clearances in the engine Note: Check the clearances on a cold engine after checking the cylinder head bolt tightening Operation 37. As necessary, add oil to the level of the check-filler hole plugged with the plug 1.
To prevent The inner cage of the reduction gear is com- turning-off the nut collar is center-punched in pressed by the collars 3 and 20 fig Д-27. The pneumatic system is also used to inflate tyres as well as for other purposes where energy of compressed air is required. Adjust oil pressure in the engine lubricating system If the oil pressure in the lubrication system of a warmed-up engine at a rated crankshaft speed is below 0. E-10 is of friction, double- from the engine crankshaft to the front and dry-disk, permanently closed type. Determine the necessity of twinning the wheels and filling the tyres with water solu- tion. It serves to transmit torque The clutch Fig.
When the disorder is found — eliminate it. Its components are unified with those of the service brake. Before engaging a gear, engage the required range stage. Turn indicator Turning the lever 4 of the steering-. To get ac- 13— Front working lights 25 A ; cess to the fuses, remove the screw on the dashboard cover and open it. Oil level in engine crank- case.
I got into the other 2 pdf's. Reduce the motor oil changeover intervals by half, if the sulfur content in the fuel is below 1%. The grasp width of the aggregate and operating depth depend mainly on the specific resis- tance of the soils, which determine the range of operating speeds with the account of agricultural requirements. E- The sets of components on the primary, 15. If guards and casings Service brake master cylinder 0.
Lower the hitch linkage to the bottom position. Before you remove the plugs, clean electrolyte density in each cell jar. In case of significant the levers connected with it. Before you start operating the tractor, carefully read this Manual and strictly follow all instructions herein. The op- tractor on the hydraulic power lift. Pump the system with manual priming pump. Tachospeedometer Р1 : 1 — Engine rotational speed indicator pointer indicator.
Do not ex- tinguish burning fuel with water 12. Clean generator Clean the generator from dust and dirt. The trailers work at speeds determined by road conditions. It can be compared to the manual you receive in the glove box of a new car. To avoid inaccuracy in 1. Alternator Remove the driving belt 1 from the alternator pulley 2. Discharge condensate from cylinders on the left and right sides of the tractor.
In this case a relevant wheels placing is required when working with standard, reverse and turning ploughs. The applied materials provide protec- 600125053. The sys- capability and issues the code information tem cannot be controlled from the main con-. A shaft lengthening is effected when lifting the implement, so it is necessary to check telescopic elements over- lap in an upper position. Turn on the pump only at the engine minimum idle speed.
E-17 and an electro-hydraulic the tractor traction and adhesion proper- control system. I aint to good with this Internet stuff. The bores for the 260. Units of system of automatic control of clutch of fan At temperature of water at output from diesel engine above 97° С fan of cooling system does not switch off, or at temperature of water below 70°. Discharge condensate from cylinders of the pneumatic system Pull the ring 1 towards and up, open the valve and hold it open until the complete condensate and dirt are fully discharged. Draining sediment from fuel fine filter Drain sediment after each 250 service hours of the engine. Stop the engine and brake the tractor with the parking brake.
Turn off the pump for engine cold start or maintenance. During operation, the left brace length can be changed from 395 to 510 mm depend- ing on the tractor delivery set and kind of 425-520 attached machines and equipment. Flush the cooling system To flush, use a solution of 50-60 g of sodium carbonate and 1 liter of water. Does this mean i have and issue with this valve? Jamming of unloading piston of diaphragm Disassemble regulator of pressure and eliminate jamming. The engine cooling system operates under pressure which maintained by a valve in the heat exchanger cap.