Just print it out and take it with you into the garage or workshop. Caution: Run the sensor line correctly. In order to perform the work efficiently and to avoid costly mistakes, read the text and thoroughly familiarise yourself with procedures before starting work. This manual is very easy to use! Caution: Use only wheel studs with length code 55. Caution: Do not accidentally confuse rocker shafts and pushrods. The brake light must come on as soon as the rear brake begins to take effect. A basic knowledge of mechanics, including the proper use of tools and workshop procedures is necessary in order to carry out maintenance and repair work, satisfactorily.
The problem is that once you have gotten your nifty new product, the R 1100 S Workshop Manual Pdf gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Providing that the service schedules are respected, the customers can be sure of obtaining the maximum satisfaction and best result from his car. Tightening torque: Gearbox to engine block. Caution: Do not touch inner surface of reflector or bulbs with bare hands. . Fully assembled length: Selector drum. Disconnect ground earth lead from battery.
Failing this, vibration could cause the screws to work loose. Hand-tighten hex nut 1 on adjusting screw 2 remove the spark plugs. Caution: Always measure taper roller bearing with oil baffle plate removed. The repair manual is structured in the logical sequence of the work to be performed: Removal, Dis- assembly, Repair, Assembly, Installation. Caution: Ensure that brake hoses are correctly located. Tightening torque: Ball joint to slider tube bridge apply Never Seez to thread. Disconnect ground earth lead from battery.
Install in the reverse order of work. Tightening torque: Big end bolts oiled Joint torque. . Install in the reverse order of work. Caution: Do not mix up the rocker shafts and pushrods.
Heat gearbox housing to 100 °C. After assembly, check fuel pump unit for leaks. Tightening torquet: Handlebar at rubber mount. Tightening torque: Ball joint to fork slider bridge. Switch off ignition, disconnect and insulate the ground earth strap. Instrument cluster, brake and rear lights. Run wiring without kinking and avoid risk of abrasion.
Keep complete records of all maintenance and repairs with dates and any new parts installed. Rectify all problems as soon as possible immediately if safety related. Caution: To ensure that the fork is installed without trapped stresses, observe the following instructions and the Tightening torque: specified working sequence precisely. Installing rear wheel Caution: Contact faces on rear wheel drive and hub must be clean and free of grease. It is important to buy the right repair manual for your motorcycle. Note: Make sure the brake discs are installed the right way round holes: see arrow. Do not touch inner surface of reflector or bulbs with bare hands.
Caution: Installing timing chain tensioning and Timing chains 3 must mesh fully with auxiliary shaft sprockets. Tightening torque: Fuel pump assembly to tank. Unscrew threaded connections 3 at instrument cluster. The repair manual is structured in the logical sequence of the work to be performed: Removal, Dis- assembly, Repair, Assembly, Installation. The oil baffle plate is slightly corrugated, which can falsify the measurement. All information, illustration and specifications contained in this manual are based on the latest product information avaiable at the time of publication approval.
Follow the procedures in this manual carefully and completely. Appropiate service methods and correct repair procedures are esential for the safe, reliabe operation of all motor vehicles as well as the personal safety of the individual carrying out the work. Tightening torque: Belt pulley at alternator. Note: If no work is carried out on the valve gear holder, re- move it together with the cylinder head. This manual also contains information about adjusting work and valuable reference data for such adjustment values.
Secure front suspension strut at bottom. This service manual has been specially prepared so that the explanation is very simple. Caution: Run the sensor line correctly. Tightening torque: M 6 screw. Note: When installing, note right and left rubber buffers 3. Valve clearances with engine cold max. Not to be reprinted, translated or duplicated either wholly or in part without prior written permission.
Timing chains 2 must mesh fully with auxiliary shaft sprockets. Tightening torque: Clutch housing to crankshaft screw threads oiled. Note: When installing, use new seals 7. Caution: Note correct direction of flow through fuel filter. Mark screws with a paint spot. The descriptions are brief but precise and are supported by photographs, notes, drawings and schematics, as well as exploded and sectional drawings.