Kelly then established an organization specializing in home improvement, including repair and maintenance of household appliances, garden equipment and lawn mowers. If there's a gray button where the hose and water supply connect, press the button to release the hose. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Then, you can remove the hose from the faucet head to replace it. Or at least until that one wears out. This could be a plastic hose, a coiled metal hose, or it could even be a solid metal tube.
Lift the disposer onto the lock ring and tighten with a screwdriver. Rotate the hot and cold-water valve knobs Figure 3 clockwise to turn the water off. Next, use an adjustable wrench and a pair of channel locking pliers to disconnect both of water lines from the faucet. Turning the handles as far as they can go in the on position may re-seat the sealing gasket in the handle and stop the leak. See below for a shopping list, tools, and steps. Give it time to soak in, and you may need more than one application.
Unscrew the lines from the faucet. Adjust the length of the wrench handle and place the jaws of the wrench around the nut underneath your faucet. Place the new faucet onto the new sink. Remove the knockout plug from the side of the disposer using a screwdriver. Close the hot- and cold-water shutoff valves under the sink.
You should wear safety glasses to protect your eyes from falling debris. Turn the water valves back on. The sprayer is held by another plastic nut. Follow This Old House and Ask This Old House: Facebook: Twitter: Pinterest: Instagram: Tumblr:. Tighten the lock nut from below with pliers.
Place a pan under the sink to catch drips. This will make your new hose easier to attach, and help prevent leaks. For example, bathroom faucets may have a pop-up drain attached. One of the difficulties in taking out the old faucet is reaching up into this tight space and gaining enough leverage to remove the connections. After the tubes are in, lower the faucet onto the sink and hold it in the position where you want to secure it. Screw on each nut by hand and tighten it down with an adjustable wrench. Together, they cited information from.
A new faucet is a great way to give a fresh look to a kitchen or bathroom. Over time, the hose that connects the water supply to the faucet in your kitchen may leak or wear out, and if this happens, you'll need to replace it. If your faucet has begun to leak, you may find that the O-ring the mechanical gasket in the shape of a ring needs to be replaced. Take the original hose to the hardware store and buy a replacement that will be a perfect match. Then use a wrench to tighten it a quarter turn. Tip: Notice that there is no need for an anti-leaking paste or tape because the supply lines have a built in gasket Figure 17c. Count the number of holes that are being used by the faucet.
The brand of the replacement faucet is Moen. You can either mount it directly to the countertop for a one-hole installation, or use an escutcheon plate also called a deckplate that will cover up the two outside holes. Unscrew the aerator from the end of the faucet. Use the appropriately-sized hex wrench to remove the hex screw holding the faucet handle in place. Comment: The faucet requirements shown in the picture Figure 13 allows for installation on a 2 or 4 hole-sink.
Remove the old faucet supply lines Image 1 , which will expose the holes in the sink. On faucets like this where the supply lines are built into faucet, any mounting hardware is made to slide directly over the lines. Others will snap in and out of place. Depending on your setup, there may be as many as 3 hoses under your sink: 1 for the cold water, 1 for the hot water, and 1 for the pull-out hose. This will prevent water from leaking everywhere when you remove the hoses. You may need to apply pressure to break any caulk seal.
Make a mark on the hose where the weight is located so you can replace it later. Take the original hose to the hardware store and buy a replacement that will be a perfect match. Install the hose, faucet head, and weight. Connect the drainpipe to the T-fitting with a compression fitting. If this is the case, turn the handles until they are completely on. Sometimes the threads are stuck with hard water deposits.
Wipe off any hard water deposits from the body with a clean rag. Then, you can remove the hose from the faucet head to replace it. Attach the hose to the faucet. If you have a garbage disposal or P-trap under your sink, unplug it or disconnect the power before moving on. Next, spin the bonnet off to expose the valve and valve mounting nut. Your local independent home improvement retailer has a variety of styles to choose from, from the simple to the extravagant, and we can often special order, so you get just what you want.