I have no do doubt that we will be able to make money with this machine. But what good does that flexibility do when you need to make 100,000 widgets in the next two years? Other way to clean power pack first or punematic line. Some push buttons and keys are used for control maintenance or special operation com- mands. Yes, I can see the need to a traditional machine, but I can't see those same situations coughing up cash to buy the manual. No readily available tool holders for that and most people make their own.
Clean up the mess, grease it up good, check the lip seal on the back of the turret you call it the tool holder plate replace if needed, assemble and put her to work. There is an electric version that has push buttons, one for clockwise one for counter, hit it as many positions as you want to go. Saldurai, Thank you for your interest in maintaining your Okuma machines. So there may be a valid use for a turret lathe. This allowed the turret to index, but it will not index to the correct tool. The innovative 3 v-way design is just one example of the ingenuity Lagun Engineering Solutions has become known for by customers around the world. On the 'Trak, the control tells the turret which tool, and it goes straight to that tool.
It is heavy duty definitely not tool room. Your local Okuma distributor is the best resource for troubleshooting and servicing your machines. The second switch confirms that the turret is actually in the right spot. But for other uses, exact copies are necessary, and it can be tough and time-consuming to create them by manual means. After we moving the machine to our shop, the back turret is operating flawlessly, but the front turret is having issues.
You'd mount the switch at the end of the travel, in X for instance, then you'd program it to hit the switch and index to the next tool. The alarm message will be cleared from the display. There should be a sheet metal cover on the right side of the turret. My step father and I have just started a machine shop. The heat exchanger provides the cooling and environmental protection necessary for proper operation of the printed circuit boards. Now is the surface of the curvec coupling machined or cast? It is mounted on the side of the hydraulic tank, as shown in Figure 3.
The lathe is a truly time-honored tool, used for hundreds of years to produce parts for machines, furniture and many other items. It unlocks or locks with air pressure, indexes with a stepper. Manual lathe would be a different story. The turret will not index. The electricals may seem criptic, but usually the ones from that vintage are pretty good. In no event will Hardinge Inc. Shops can generally purchase these machines at very reasonable prices.
Your local Okuma distributor is the best resource for information about preventive maintenance, service, and parts. The pH of water based coolants typically runs on the alkaline side of the pH scale. But your point is well taken in that if one actually needs to use 8 different tools, you've sort of stepped into the territory of really needing a proper hydraulic turret slant bed turning center. Instead of being tied to the lathe for hours, you can design the parts you need and let the computer handle the controls, freeing up your time for other work. I think you will find and aluminum arm and a circuit board with 16 glass reed switches.
It has severe pitting issues. I hope the turret is not sloppy loose when assembled after removing the rust. Long before automatic toolchangers were applied to milling machines, the lathe had a multiple-tool configuration. I've heard you can't get rough with them, but it works well for me, using ~100 psi. Not to bad for small drills but larger ones are tough to mount.
There are also cnc programming examples using macros. Best Regards, Mindy Mikami Marketing Coordinator Okuma America Corporation Prakash, Thank you for your comment. Then is stops and clamps. If the switch is turned clockwise while turret is spinning it wil sit down. Much easier on a turret like the Dorian. But if you have a preventive maintenance program in place this allows you to manage your schedule rather than getting caught with untimely surprises. Clean up the mess, grease it up good, check the lip seal on the back of the turret you call it the tool holder plate replace if needed, assemble and put her to work.
The turret drawing shows a shaft with an angled recess in the shaft. But a steel pattern is lot more reliable than all the computer hardware needed to get a program to run. The rear turret has reed switches in it for location. I am in the process of making a replacement. It doens't cover moving parts, checking backlash, filter changes, or any of what you have listed above. Milltronics switched to Pragati turrets about 2002 or 2003.
It is equipped with an 8 position front turret o. Wait for the cycle to end and that the spindles and slides are stationary. It seems to me that if you don't have a turret that indexes via the control, you would be just as well off, and a lot cheaper, with a quick change like Aloris. Refer to the appropriate power-down procedure in Chapter 1. The lathe follows the exact same instructions and follows the same cutting path each time for parts that are exactly the same.