Avoid wave or wake jumping whenever possible. Some repair procedures in this 25 horsepower outboard downloadable manual may require the use of special tools. This steering torque is a normal result from your outboard not trimmed with the propeller shaft parallel to the water surface. Set the spark plug gap to specifications. Lower the top cowl over the engine. Do not allow any passengers to stand or use seats other than those designated for traveling faster than idle speed. Any unexpected, sudden reduction in boat speed could result in the elevated passenger falling over the front of the boat.
Use of other than Mercury Precision or Quicksilver parts when making warranty repairs. Do not install an engine that exceeds the boat's maximum power rating. Install the steering cable and tighten the steering cable nut to the specified torque. The outboard marine mechanic should carefully read the text and become familiar with the 25 hp marine engine service manual procedures before beginning the work. Oils, lubricants, or fluids changed as a matter of normal.
The use of clamp bracket screws alone, is insufficient to properly and safely secure the outboard to the transom. Mercury 4-Stroke Outboard Boat Motor Service Manuals Please visit our brand new to see a complete list of all available Mercury 4-stroke outboard service manuals. Route the harness between the barrel support. If the boat turns more easily to the left, move the trailing edge of trim tab to the left. Position the tilt lever to the tilt position. Individuals using this 25 hp outboard marine repair manual should possess basic knowledge of tools and mechanical theory.
Squeeze the fuel line primer bulb several times until it feels firm. Make sure the cooling water intake is submerged. Allow rope to return slowly. Lubricate the seal on the drain plug with oil and reinstall. The outboard marine mechanic should carefully read the text and become familiar with the 25 horsepower marine engine service manual procedures before beginning the work. Push the dipstick back in all the way. Disengage the tilt support lever, by slightly tilting up the outboard and releasing the tilt support bracket.
Keep the boat well ventilated while at rest or underway and avoid prolonged exposure to carbon monoxide. Remove the access cover and cable rubber grommet. Individuals using this 25 horsepower outboard marine repair manual should possess basic knowledge of tools and mechanical theory. The operator of the boat is responsible by law to maintain a proper lookout by sight and hearing. Idle engine for five minutes and check for leaks. Store the outboard in the full down position. Insert a new cotter pin in the hole and bend the cotter pin ends.
The following information explains some of the types of services that are not covered by warranty. To release the outboard out of shallow water drive, position the tilt lever to the release position, and slightly lift up the outboard, and than gently lower it down. This would occur if the operator accidentally falls overboard or moves within the boat a sufficient distance from the operator's position. Do not spray on corrosion control anodes as this will reduce the effectiveness of the anodes. However, to ensure extended life of the outboard engine, Mercury recommends that the oil and filter be changed regularly following the oil change interval and using the recommended oil quality.
Replace fuse with a new fuse with the same rating. If water is present, it may have settled to the bottom and will drain out prior to the lubricant, or it may be mixed with the lubricant, giving it a milky colored appearance. Apply marine sealer to shanks of bolts. Sit only in seats designated for traveling at faster speeds. The provisions set forth following have been incorporated by reference into the Three Year Limited Warranty Against Corrosion Failure, the International Limited Outboard Warranty, and the United States and Canada Limited.
Lift up on the rear of the cowl and disengage the front hook. Install the spark plug leads. The problem is that once you have gotten your nifty new product, the mercury 25hp bigfoot outboard service manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Insert a new cotter pin in the hole and bend the cotter pin ends. Align the propeller nut with the propeller shaft hole. Proper installation of the outboard includes bolting the engine to the boat through the transom. Tiller handle models will have the warning horn located in the engine cowl.
Never operate the boat out of the water with a propeller installed. Turn the steering on the outboard so that the drain hole is facing downward. Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from starting. Lift rear of cowl and disengage front hook. Corrosion damage caused by improper application of copper base antifouling paints is also not covered by this limited warranty. Provide a sufficient supply of water to the water inlets during operation.
Shift remote control into reverse while turning propeller. Accidental or unintended activation of the switch during normal operation is also a possibility. This can result in an unexpected turn in either direction called bow steering or oversteering if any turn is attempted or if a significant wave is encountered. Straighten and remove cotter pin. Push tiller lock release lever to release the handle from the locked up position. Locate the center point of the slack or lost motion that exists in the shift cable as follows: a.