Download the files I forgot to include nandpro get that Extract the rar, and open up the nandpro folder install port95nt. The best tip I can give you is to heat up the spot you are going to solder for a second or to, then apply some tin and remove the tin and iron. Xexmenu does not find any games? Plug your Xbox 360 in, but don't power it on. This should cause the tray to open a small amount. I never use flux on solder spots like these, the tin you use is likely to have a resin flux core.
You can also launch games off the hard drive without a disc. Use this to download the latest files. Then, securely holding the console, use your thumbs to pull the faceplate off the front of it. Manually eject the tray Start off by shutting down the console and removing all the cables plugged into it. We also provide instruction for how to jailbreak a too. Disconnect all cords from the Xbox.
Soldering irons can be very hot and cause burns, as well as possibly break your Xbox 360. If you are having issues having nandpro detecting it, go over and double check all of your soldering. I also put the resistor leg on the motherboard because they were easier to solder in to place. You only have to solder the white shielded cables inside as these are the data cables. And last thing i run all the games from the normal game menu. Close the window which opens. Take off the faceplate by pulling on it.
Had to look at other guides to figure out how to get it working. A lot of them will come in handy with your Xbox 360 homebrew experience. It's supposed to auto install the temp jtag. Either in the beggining of the reading or the end but will most likely turn it self off again. It is still possible to add a mod chip to a game system, but that there many cautions that come with installing this type of chip. A shorten the wires and redo soldering spots. I've never used this method before so I can't really help as much if you have problems.
It is one of the most progressing dashboards that is constantly being updated with new features. There are many spots on the Xbox motherboard where you can get 12v of power from, I picked the power connector on the bottom of the board as I'm not soldering onto any other connectors or anything. Insert a paper clip into the leftmost hole and push until you feel it hit something. Soldering is generally pretty straight forward. But I'm not sure of the mobo but I have opened it just never paid any attention.
Be very careful to ensure the disc tray does not close, as it would be difficult to reopen without the rubber band in place. So you just need need to heat it up and slide the wire through. Have no idea where to start? Straighten out a long paper clip and insert it into the hole, about an inch and a half. Inserting a credit card horizontally into the top of the closed disc tray, press the eject button and when the clicking noise occurs bend the credit card back toward the console, applying leverage to force the tray open. The disassembly process for an Xbox 360 classic model is different than the disassembly process for an Xbox 360 Slim or an Xbox 360 E. These are the grey lattices on the left and right ends of the Xbox 360 case. Repeat this process with the other file.
Obtain a copy of Splinter Cell. The original Splinter Cell can be used to access the mod files for your Xbox. Flashing is possible but I don't really advice it anymore as it's tedious. And for writing the nand. Move the console to a horizontal position and search the vents on the left side of the console for a yellow sticker. This will unhook the clips holding the grille. I'll be going over what each program is good for.
Keep in mind that disassembling your Xbox 360 console will void your warranty. This means a person copied the game to a device. While holding the tray open, carefully rewrap the rubber band back around the cylinders they were on. This wikiHow teaches you how to modify your classic Xbox console to allow for custom software. Here we have mentioned the instruction below.
I suggest you work on your soldering skills as I have personally never had issues dumping, but then again I have a background in electronics. Remove the end grilles with a flathead screwdriver. After jailbreaking your Xbox 360, you can backup games directly to your console, play new file formats that were previously unsupported, install game mods, and run third-party software not supported by Xbox 360. With any luck the newly cleaned opening mechanism will solve your disc tray issue. Often the paste comes separately from the solder.