Step 2 - Cut Replacement Patch from Sheetrock From sheetrock, cut a patch the same measurements as the hole you knocked from the ceiling. Cut out any rough spots or jagged edges from the patch or the ceiling if they prohibit the patch from fitting in the hole. Step 6 Apply joint compound to the seams and apply paper tape resulting in at least and inch and a half overlap at the corners. Let the blobs dry for about 10 minutes before lightly dragging a wide drywall blade over the slightly wet blobs. Immediately go back over it to skim off the excess using parallel strokes from one side to the other. If the scrap you are cutting from is thinner that what is in your ceiling, it is because the scrap is from a sheet meant for the wall.
One of the best is screwing pieces of plywood to the insides of the hole, so you don't have to buy a specific product made for that. Sand if necessary to remove any other roughness and wipe off the dust. The lynchpin of my process is watering down the spackling compound slightly before applying it. Most diy people would be good using just the lightweight stuff for every step. Step 4 For larger repairs, fasten with screws and a set of parallel backers. Prime the texture with drywall primer when it dries and then paint it with the ceiling color. The thickness of the hole saw blade makes it easy to slide the plug into the hole because the plug is smaller than the hole.
Patching a drywall hole can be relatively quick and simple. Our plumber had to cut a hole in the ceiling of our main level bath to fix the slow draining bathtub on the second floor. I live in rentals so have very few tools or materials on hand. Allow the final coat of mud to dry completely and then sand the whole area. Cut a bit past the pencil mark at each corner to be sure the new drywall patch will fit easily without forcing. Use a medium utility knife to smooth out the tape.
For smaller repairs, place clips on each side at the minimum, or attach with backers. There are easy ways to fill and patch a small hole in your damaged drywall. It might be more noticeable in the middle of your dining room but it may be an easy and inexpensive option. Came out nice though, its rare to see a home owner do any spackling where you cant see it after its painted. Disclaimer: Posts on this website may contain references to products from one or more of our advertisers. If the hole in the ceiling is 4 by 4 make your drywall scrap 6 by 6. Attach the patch to the wood support structure with drywall screws.
Understand what the levels of finish are, and you'll be better able to schedule your job. Step 1 Begin by making sure the mode of attachment has been fully removed. Smooth with a large knife repeatedly and often, feathering at the edges and starting and finishing from different directions. Step 8 - Sand Before Priming and Painting Finally, sand lightly before and after applying the final coat of compound. The step takes a bit of trial and error until you get the right look, but this method works really well. Let the patched area dry before continuing.
Let the patched area dry, then add additional coats if necessary. Allow it to dry in between additional coats. If you are using semi-gloss or other shiny finish paint, prime the patch first with flat latex paint or a latex primer before touching up. Please see the guidelines link above. In this way, the edges of the patch will feather into the wall and be invisible. Just clean it immediately after use, so nothing clumps up in your bristles. Make the mud as smooth as you can, but don't worry if it's not perfect.
Add areas of texture until the patched area matches the surrounding ceiling texture pattern. These are available at big-box home centers and hardware stores. Sheetrock comes in various thicknesses. Wetting the patch in advance helps the paper stick to the joint compound. Apply two coats of primer to the repaired area. Although not a particularly fun project, this type of repair is a task that an average homeowner can accomplish successfully. At this point, you just need to apply the spackling compound as normal.
Hot patches, california patches, boston patches, french patches. Spread the joint compound around the perimeter of the hole with a 4-inch drywall knife, moisten the tape and lay it over the hole. Damp wiping is cleaner than sanding, but use it sparingly. Feather outward as you apply mud so that the mud reaches out farther than the original damage. At this point, the patch should appear flat and even with the surrounding area, unnoticeable except for the lack of texture. Image: Debbie Williams Knock Down the Spray Texture Start with light coverage, wait a few minutes, and knock down the splatter with a wet drywall blade if applicable.
Just use this coat to stick the tape down and start to blend the new patch with the surrounding wall. To create this article, 49 people, some anonymous, worked to edit and improve it over time. The plumber got a white snap-in cover panel and covered the hole without having to use drywall patch or paint. Then plugs could be glued or screwed to the wood. However you can get pretty close with the finger method. If you're going to add texture, use a scrap piece of anything to make sure you're matching the texture pattern.
Apply self-adhesive fiberglass drywall tape to the perimeter, spanning the space around the patch. Probably took me 90 seconds to get the sheetrock patch in once I had it cut to the right size. As you may recall, last week, we in our dining area, which left us with a nice round hole in the ceiling where the previous light once hung. Image: Debbie Williams Spray on Drywall Texture Aerosol knock-down texture is generally made for walls, so the cans are designed to spray at a 90-degree angle. Use a sharp utility knife to trim away any loose or protruding paper facing or loose pieces of gypsum. The teeth will grab the surface of the drywall, and on big holes this will cause the drill to jump around. Pull the blade toward you in one steady, smooth motion.