I did reverse engineering and that what I came up with: The yellow wire needs to be connected to white and both connected to neutral white. Sync Wall Control Turn the power on at the circuit breaker and wall switch. Lift the lower switch housing up and line up with the screw holes in the upper switch housing. Other items you will need are electrical tape and wire strippers. Ensure the power is off by using a on the switch or light sockets. This is typically due to either many wires inside, or the junction box is not deep enough to hold the space.
Once you are ready to start, you will need the following materials and tools. If your ceiling is 15 feet or higher, choose an 11-foot stepladder. This guide is for ceiling fans that are already installed. The instructions should outline safe lengths. There sometimes can be other variables when installing a remote and receiver for a fan, such as the receiver not physically fitting inside the canopy. Now that we have these cool blades installed, we're going to install the light kit.
Double-check that it is off by mounting a ladder to the ceiling fan. There is no directional control on the universal remote, but I understand that reversing the yellow and pink wires will make the fan blow upward. There are many types of remote controls for a ceiling fan. There are also wall-mounted remotes as well, which are typically wired differently. Install the battery for the remote. Use a screwdriver to tighten and secure the screws on the motor housing and blades to prevent any wobbling or shaking.
I don't know what these parts are much less where they go. For example, you might need to rotate the canopy to reveal the screws, or you might need to remove the blade brackets to allow the housing to drop. Spread wire connections apart, with the grounded wires on one side of the box and black wires on the other side of the box. Step 4: Connect the wires Before disconnecting the existing ceiling and fan wires, take a few photos for reference. If the fan won't start. We've got this light fixture in a popular area in the home and in the summer it just gets a little warm and in the winter it gets a little too cool. Hi Viktor, Please be aware that this article refers to a Hunter Fan, Model Number is 21871, and the Universal Remote is for the hunter fan.
Contact the manufacturer for warranty information or replacement options. Now that we got through the hard part, we're going to go ahead and install the ceiling fan blades to the motor housing. Name required Email will not be published required Website By submitting you agree to our. Enjoy your new ceiling fan remote. When the light kit on a ceiling fan isn't working. Most people believe that the hand-held remote is the only part when it comes to repairing or installing it. So we want to install a ceiling fan with a light kit, so that we can recirculate the cool air in the summer and recirculate the warm air in the winter and also have proficient light for all the tasks we need to do in the area.
Since we're installing a ceiling fan with a light combination, we're going to want to use a remote controlled or two wire wall control so that we can control this ceiling fan separate from the light. Since the receiver is inside the fan, it is typically looked over the first time troubleshooting is done. Now restore power and ensure the remote works by following the instructions. Pull the electrical box through the opening in the ceiling. If you see a white wire, test it to determine if it is hot. Wiring will vary according the manufacturer.
Another view of a wiring diagram is shown below, similar to one shown earlier. For this ceiling fan installation video, we used. Push the canopy or housing back into place to get a sense of how the receiver fits. However, certain brands and models have specifics that are worth explaining. I purchased them both at home depot. Install New Outlet Box Remove a knockout on the outlet box and attach a cable clamp.
Some brands may include a screwdriver in the packaging. Most, but not all, receivers are installed above the fan motor in the ceiling canopy. Turn the connections up and push them through the hanger bracket into the outlet box. Feed the supply line through the clamp so the line extends 6 inches from the box. Next, you will need to remove the canopy on the ceiling. Insert the canopy screws provided into the holes and secure tightly.
Remove Existing Electrical Box Remove any screws and washers with a screwdriver. The method of reverse engineering is a good idea, however be sure to refer to the wiring diagrams and instructions that came with the specific remote control unit and the ceiling fan that you have. This is typically due to either many wires inside, or the junction box is not deep enough to hold the space. Most people believe that the hand-held remote is the only part when it comes to repairing or installing it. Hunter Ceiling Fan and Remote Control Module Ceiling Fan Question: How do I wire a universal remote control for my ceiling fan?. The most common screwdriver types are flat-head screwdrivers and Philips screwdrivers.