Keeway f act manual. Keeway F 2019-01-26

Keeway f act manual Rating: 8,5/10 504 reviews

Print & Online Keeway Scooter Repair Manuals

keeway f act manual

If necessary, change a new one. Screw Remove the magnetic motor, rotor and bracket. Loosen set screws of turn signal lamp 3. Remove the rear container, rear shelf assembly, rear fender. The tire pressure is too low. Start the motor or step on the actuating lever to determine the maximum voltage of charging coil.

Next

KEEWAY Manuals

keeway f act manual

The hoop-claw part of the body should not be damaged when being assembled and disassem bled. The front wire deforms or skews. Preparation Standards Item Standard Value. In case the brake fluid level is at or below the arrow in the picture, certain brake fluid shall be added until it reach upper limit. Table 1-31 Name Note avometer Figure 1-33 ignition tester Figure 1-34 Continuation Table 1-32. Replace it with a new one. If there is odd voice or loose, please change the crank axle component.

Next

Keeway F

keeway f act manual

Take off the bulb socket. Supplement gear oil, Check if there is leaking oil Install gear oil to check bolt. Attentions: The spring should be compressed appropriately, otherwise it would be damaged. Battery charge and discharge can be repeated use, its life span can be shortened and performance decreases after discharging. Remove the front big cover component.

Next

KEEWAY Manuals

keeway f act manual

Wind guiding cover Loosen the screw on the fan and remove the fan. The special tools can assemble and disassemble parts safely, dependably and quickly, which can improve working efficiency by saving labor and energy. Cylinder pressure Operate when the engine warm up. Each plug of the machine oil pump should not leak and the sealing ring should be complete. Check if the piston ring sticks fuel cock block in ring groove or insufficient 3. The transformed accelerant contains Platinum and Rhodium and other rare metal. Gear Dismantle the fixed bolt of crankcase Gear Dismantle the crankcase on both sides.

Next

Print & Online Keeway Scooter Repair Manuals

keeway f act manual

Before the maintainence operation of disconnecting or opening the protecting plate, please eliminate the pollution outside the parts or assembly parts to prevent the pollution fall into the motor, bottom plate or brake system. Change the front brake disc and friction plate component, if their thickness are less than the standard value or they have been polluted. Attentions: Bearing When pressing the outside rolling bearing into the bushing, screwdriver the side with mark should be placed outward. Right half components of driving wheel 14. Remove the cover of battery box. Install the solid key of the flywheel into the bent axle. Pull out the inlet oil hose and to loosen the guy wire of oil Electrical valve.

Next

Print & Online Keeway Scooter Repair Manuals

keeway f act manual

Remove the cushion and helmet bucket. ·The wire should not be pulled and bended with force, since deformation and damage will affect the its performance. Dismantle the floating module, floating pin and needle valve module. Remove the rear container assembly. Put the fuel oil interface in the floating bowl into another box.

Next

Keeway F

keeway f act manual

Wear of the brake shoe block and friction plate component 2. If necessary, time should be limited. Dismantle the cylinder Cylinder Fixing nut cover. Conduction check of the outer cover of the starting motor. Remove the rear axle fixing nut. Piston pin, retainer Check piston, piston pin and piston ring Remove piston ring Attentions: do not break or damage piston ring To remove the carbon deposits in the piston ring groove Remove piston rings and put them in the bottom of the.

Next

Print & Online Keeway Scooter Repair Manuals

keeway f act manual

Remove the front shield and disconnect the wire of headlight bulb. Check if the venthole of in external connections of the fuel tank cover blocks engine 2. It should be removed if there is any oil left so as to reduce the slippage between v-shaped belt and pulley. The brake shoe block and friction being polluted Slow response of the brake or the tightness of the handle 1. Tools: Direction handle welding component fixing bolt wrench. The speaker is good, if it can sound after The speaker wires connect to a storage battery. To check the flatness of the bottom plan of cylinder cover Acceptable limit: 0.

Next