If any irregularities are found during these checks, refer to the Maintenance and Adjustment chapter or see your dealer for the action required to return the motor- cycle to a safe operating condition. While checking female rod to mainshaft clearance, observe clearance between crankpin end of female rod and rim of both flywheels. Available in the following sizes: 35-8439 4. Wristpin end to crankcase and cylinder —. Tire Pressure Gauge Tire Air Pressure when cold Front 150 kPa 1.
Providing that the service schedules are respected, the customers can be sure of obtaining the maximum satisfaction and best result from his car. When the isolation valve is completely closed, the valve plug is in contact with the full height of the valve sealing rings, ensuring the best possible seal. The slotted holes allow adjustment of the valve timing. To download your manual for viewing or printing please click on the blue links below. Depending on the problem, these simple steps may help:! Discard parts from the installation kit that are not required. Clearance at every coil should be at least. Check to see if bonnet is seated on the body, if not, tighten the bonnet nuts until the bonnet seats.
All products are subject to change without prior notice or obligation. Make sure the area is well-ventilated and free from any source of flame or sparks; this includes any appliance with a pilot light. It has been prepared so that if this manual is thoroughly read, even comparatively new personel can give satisfactory after services to the customers as well as disassemble and maintain the vehicle. Turn Signal Indicator Light Right I. Do not remove material from connecting rod. Rotate rods on crankpin, and observe clearance between rod and sprocket shaft nut.
Available in the following sizes: 35-3829 4. Overall Height 1 090 mm 42. If a fuse portion with bare hands. The descriptions are brief but precise and are supported by photographs, notes, drawings and schematics, as well as exploded and sectional drawings. If it is not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Return spring not weak or not damaged. The bonnet compresses the valve sealing rings against the body and the valve plug.
Valve clearance for each valve should be checked and adjusted in ac- cordance with the Periodic Mainte- nance Chart. Rectify all problems as soon as possible immediately if safety related. In extreme cases, a valve head may strike the piston crown, causing extensive damage to the engine. With the camside flywheel and rods mocked up, install the assembly in the right crankcase half with pistons less rings and cylinders in place. This manual provides general descriptions for accomplishing service and repair work with tested, efective tehniques. Sold as a kit with coarse 120 grit roughing and 280 fine grit finishing. If this is not practical, a 12 heating and damage may occur.
A break-in period of 160 km 100 miles is necessary to establish normal tire traction. Remove the gearchange pedal and the left-hand outer cover to expose the generator rotor. If you happen to spot a broken link on our website while trying to download 2015 Klx 125 Service Manual pdf, please inform us about that so we can fix it and help you obtain the file you need. Low compression top end needs a rebuild. The answer is simple: you have already found the book or handbook you were looking for, and it is available for download in a variety of the most common formats. The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve.
File or grind crankcase or cylinder spigot as needed to achieve. Follow the procedure detailed in section 3 of the Daytona 675 service manual. These operations are very important to engine life, please follow instructions! The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. If additional clearance is needed, remove material from sprocket shaft nut. The problem is that once you have gotten your nifty new product, the Klx 125 Service Manual Pdf gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Horn Button When the horn button is pushed, the horn sounds. Be sure that Vertical Adjustment the wire connections are clean.
Stand upright the ve- hicle to check the fuel level. Blank keys are available at a Kawa- saki dealers. For each fluid level in both the front and rear front and rear disc brake caliper, if the brake fluid reservoirs and change the thickness of either pad is less than 1 brake fluid. The illustrations in this manual are used to highlight the fundamental principles and procedures of basic interventions. To stop flashing, push the switch in. Use on twin or four cylinder heads. The key can be removed from Engine on.
Air cleaner not sealed properly or missing element. This motorcycle is equipped with a catalytic converter in the exhaust sys- tem. Information on the troubleshooting, servicing specification lists, tightening torque, checking and adjusting, disassembling and assembling and servicing which cover procedures, precautions, factory specifications and allowable limits. Wax should chemical substances or house- be applied once every three months or hold cleaning products such as as conditions require. Check to see that the handlebar turns freely but has no play. The battery is not fully charged 12.