Manual apc smart ups 1500. Read Smart 2019-03-12

Manual apc smart ups 1500 Rating: 6,2/10 1027 reviews

SMT1500I

manual apc smart ups 1500

Contact a qualified electrician to correct the building wiring. Continuous Tone - this alarm is sounded whenever the Battery Backup outlets are overloaded. During the second beep, release the button. Test the input voltage with the utility voltage display. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Next

APC Back UPS XS 1500 user manual

manual apc smart ups 1500

The packaging is recyclable; save it for reuse or dispose of it properly. The battery is disconnected or must be replaced. Add optional accessories to the Smart-Slot. · Increase the separation between the equipment and receiver. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. If the battery fails again, it must be replaced. Contact a qualified electrician to correct the building wiring.

Next

APC Back UPS XS 1500 user manual

manual apc smart ups 1500

Press and hold the button to view the utility voltage bar graph indicator. This warranty does not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in any way. Inspect the equipment upon receipt. Reset this date when you replace the battery module. Whenever possible, the output frequency tracks the input frequency. Exit the PowerChute Business Edition software. Caution Refer to the appropriate replacement battery user manual for battery module installation instructions.

Next

APC Back UPS XS 1500 user manual

manual apc smart ups 1500

Failure to follow these instructions could result in cabling shortage. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. These units support up to ten external battery packs. The unit will emit two beeps. Failure to comply with safety instructions could result in bodily injury or equipment damage. Check that the battery connectors are fully engaged. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Next

APC Smart UPS 1500 VA, Smart UPS SUM3000RMXL2U, Smart UPS 3000 VA User Manual 3

manual apc smart ups 1500

Re- lease the button during this beep. On Line On Battery Overload Replace Battery w w w. Place a protective sticker or packaging between the battery connectors to ensure that the connectors do not become re-engaged during transport. ­ For installation in other countries: Use standard low-voltage cable in accordance with national and local regulations. If the light is very dim, have the utility voltage checked. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Place the sticker on the back of the battery cover for re-use.

Next

Need Manual for Back

manual apc smart ups 1500

Very low or no utility voltage. Damage sustained in transit is not covered under warranty. Chirps for 1 Minute Every 5 Hours - this alarm is sounded whenever the battery has failed the automatic diagnostic test. Do not attempt to reinstall it. Products must be returned with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. Mute ongoing alarms or disable all alarms permanently. Configuration Settings Settings are adjusted through PowerChute software, optional SmartSlot accessory cards, or in terminal mode.

Next

Need Manual for Back

manual apc smart ups 1500

Turn on all connected equipment. Copyright Notice Entire contents copyright © 2004 by American Power Conversion Corporation. Terminal Mode Configuration Terminal mode can only be used with the serial cable. This is a fault condition, which may be caused by an overload or a failure within the module see Troubleshoot- ing. Low Battery Warning 2 minutes 2, 5, 8, 11, 14, 17, 20, PowerChute software provides automatic, 23 minutes unattended shutdown when the remaining battery runtime matches this setting while on battery. Change the low battery warning interval setting to the time that the operating system or system software requires to safely shut down. The self-test does not affect the voltage display.

Next

APC SMART

manual apc smart ups 1500

Basic operation, user configuration, and software utilization can now be performed as required. The line voltage is extremely high and should be checked by an electrician. Never use Styrofoam beads for packaging. Manual: Press and hold the button for a few seconds to initiate the selftest. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Replacement is a safe procedure, isolated from electrical hazards. Follow the prompts to choose a name and select an icon.

Next