Sharp ar m550n u ar m620n u ar m700n u service manual. Instant manuals For SHARP AR 2019-03-25

Sharp ar m550n u ar m620n u ar m700n u service manual Rating: 4,5/10 1215 reviews

Sharp Ar M620n

sharp ar m550n u ar m620n u ar m700n u service manual

This device is used to detect a laser trouble. The trouble position can be identified by the data. This data can be used to identify the trouble position. Refer to Front panel spec. Open when a misfeed has occurred in bypass tray or large capacity tray. Left vertical transport unit 1 Remove the left lower cabinet unit.

Next

SHARP AR

sharp ar m550n u ar m620n u ar m700n u service manual

Standard setting Trailing edge void area: 3. Parts replacement 1 Parts replacement Replacement parts No. The trouble history of paper jam and misfeed is printed. The paper feed tray 2 is used for A4, 11 x 8. Toner hopper remaining quantity detection Stores the toner bottle information. Note: Never use something with a sharp tip such as a needle or pin to press the touch panel. Perform only the necessary adjustments according to the need.

Next

Instant manuals For SHARP AR

sharp ar m550n u ar m620n u ar m700n u service manual

Document table mode Adjustment Picture quality Image position 5 Used to adjust the print image position and the void area image loss on print paper. Discharges paper to the paper exit tray. Fusing section This section performs the following functions and operations. Other modes The display is made according to the selected mode and the item. Open the door, and remove the cabinets. Suppresses skew to the minimum by restricting the paper width.

Next

Sharp Ar M620n

sharp ar m550n u ar m620n u ar m700n u service manual

Detects the paper empty and upper limit tray. Adjust the copy density in photo binary mode This adjustment is intended to customize the copied image density settings. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Adjustment mode selection 1 Go through the modes specified in Simulation 50-12. Transfer roller 3 Remove the upper transfer roller unit. Process exhaust fan motor 4 1 Remove the rear cabinet.

Next

Sharp Ar m550n u Ar m620n u Ar m700n u

sharp ar m550n u ar m620n u ar m700n u service manual

Then tighten the screw of the drive unit securely. Transports paper transported from the paper exit roller 1 to the transport roller 3. The time entered in procedure 1 is set. This adjustment is intended to the print mode for each Fax mode individually. Adjustment Paper feed Operation 7 Used to enter the manual paper feed tray paper width adjustment value.

Next

Sharp Ar M620n

sharp ar m550n u ar m620n u ar m700n u service manual

Nordic swan Sharp: Follows the Green Product Declaration. Applies a pressure to paper and the resist roller to provide transport power of the transport roller to paper. Toner hopper unit List of Replacement Parts 1 Remove the toner bottle. The set value is stored, and the voltage corresponding to the set value is outputted for 30sec. Operation, display parts 1 2 3 4 5 6 7 8 Parts No.

Next

Sharp AR

sharp ar m550n u ar m620n u ar m700n u service manual

If not, the scraper may be deformed and the pressure roller may be damaged. . An optional print density can be set for each density level display value. The confirmation to clear is opened. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Heater lamp 1 A a-5.

Next

SHARP AR

sharp ar m550n u ar m620n u ar m700n u service manual

Transports paper from the fusing roller to the paper exit roller 1. The transport speed is changed to the high speed in the Following positions: 1 From when the paper rear edge passes the fusing section to when switchback operation is started. Torque limiter 1 Remove the cabinet. Operational descriptions 2 At the same time, the paper feed roller rotates to feed paper to the transport section. Paper feed tray 1, 2 The paper feed tray 1 is used exclusively for A4 11 x 8. Thermistor 3 1 Remove the fusing unit. This simulation is used when the customer forgets the key operator code.

Next

Sharp Ar M620n

sharp ar m550n u ar m620n u ar m700n u service manual

Transport roller 3 Drive a-6. Scanner lamp 1 Remove the table glass. Repeat the above adjustments until an acceptable result is obtained. The default of threshold value is 128. Adjustment Used to adjust the print density for each density level display value in the copy mode binary - Photo mode. After completion of setting, the machine is automatically reset. Distortion Print horizontal line Sub scanning direction Copy Magnification magnification precision Normal copy 100% ± 0.

Next