I718H1140389-01 4 Start the engine. I718H1110251-01 2 Check the throttle position data. Remove the oil filter 1 with the special tool. Information label — For E-03, 28, 33 3. Control Functions, Specifications, and Operating Instructions. Check and adjust the wheel balance in the following procedures: 1 Removal the wheel assembly.
I718H1140041-01 Cylinder 1 Disconnect the water hoses 1. Combining heavyweight power with distinctive styling and the quality of an all-new, technologically-advanced liquid-cooled engine and an advanced digital fuel injection system to meet Euro 3 emission regulations. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. I718H1110251-01 2 Check the secondary throttle actuator position sensor data. Tighter spacing between the two pairs of cylinders makes the cylinder head and the throttle bodies 20mm narrower, which means the Bandit can be thinner at the front of the seat and at the rider's knees--making it easier for the rider to touch the ground at a stop. Rear brake master cylinder mounting bolt 23.
The transmission shafts are staggered vertically to make the engine shorter front to rear. The fuel in the fuel tank 1 is pumped up by the fuel pump 2 and pressurized fuel flows into the injector 8 installed in the fuel delivery pipe 5. Clamp :After positioning the clamp with the stopper, tighten the clamp bolt. Engine sprocket outer cover cushion 2. Join our community just now to flow with the file suzuki gsf1250 gsf1250s gsf1250a gsf1250sa bandit service repair manual 2007 2008 2009 download and make our shared file collection even more complete and exciting. Inner tube slide metal 21. Cylinder Bore Measure the cylinder bore diameter at six places.
The cam chain tension adjuster is maintained at the 4 Remove the cam chain No. Replace engine oil Initially at 1 000 km 600 miles, 2 months and every 7 Rotate the engine so that the tappet is depressed 6 000 km 4 000 miles, 12 months thereafter. Special tool A : 09913—70210 Bearing installer set I718H1520009-01 Countershaft Assembly 1 Remove the bearing retainer 1. Air bleeder : Apply grease. I649G1220013-03 I649G1220017-03 9 Remove the oil seal stopper ring 9. Check the brake hose and hose joints for cracks and fluid leakage.
Special tool : 09900—06108 Snap ring pliers I718H1520010-01. If the the starter relay with a new one. I718H1450066-01 Is the sensor mounted securely? I718H1140037-01 9 Remove the dowel pins. Brake adjusts, Cable adjusts, Fluid Changes and more. Noise label — For E-03, 24, 33 2.
Oil seal stopper ring 12. Disassembly 1 Remove the air vent bolt 1 if necessary. Troubleshooting Step Action 1 Remove the seat. Removal 1 Remove the rear wheel assembly. Poor contact of generator lead wire Repair. B718H11B06002 Removal 1 Loosen the muffler connecting bolts 1.
When you touch the bulb with your bare hands, clean the bulb with a cloth moistened 2 Remove the tool set 1 and disconnect the turn with alcohol or soap water to prevent. Both the Bandit 1250 and the Bandit 1250S feature fully floating 310mm in diameter dual front brake discs with 4-piston calipers, along with a 240mm in diameter rear disc and single-piston caliper. Using this repair manual is an inexpensive way to keep your motorbike working properly. I718H1450097-01 Are the sensors mounted securely? Installation Install the swingarm in the reverse order of removal. Troubleshooting Step Action 1 Inspect the clearance between the rear wheel speed Go to Step 2.
I718H1140134-01 Assembly Assembly is in the reverse order of disassembly. If the level is below the lower line, add engine coolant to the full line from the engine coolant reservoir tank filler. Tightening torque Front brake pad mounting pin a : 16 N·m 1. Special tool A : 09920—53740 Clutch sleeve hub holder : 09920—31020 Extension handle 6 Tighten the clutch sleeve hub nut to the specified torque. The new engine is more compact. I718H1110251-01 2 Check the manifold absolute pressure 2 data. Once the nuts have been removed, they are no longer of any use.
Use nonflammable cleaning solvent to wipe off oily or greasy matter and make these surfaces completely dry. The Bandit 1250S comes with a half-fairing, with a built-in line-beam headlight, a windscreen and fairing-mounted mirrors. Use this section as well as other sections to use as a guide for proper inspection and service. Before inserting piston into the cylinder, Subtract the piston diameter from the cylinder bore check that the gaps are so located. Tightening torque Handlebar holder set nut a : 45 N·m 4. If the Inspection resistance is not within the specified value, replace B718H11906008 Check the interlock system for proper operation.